Browse repository
Stratigraphic unit type
11-18 of 18 results
 1 / 2 
    Previous / Next   
ID  2231  -  Public access
Description :   UE228. Cut of circular form in plan, approximately 15 cm in diameter and a maximum depth of 11 cm. The walls fall inwards at an angle slightly greater than 90º until they reach the bottom. The base, slightly oval (8 x 6 cm), is concave with relatively soft ruptures with respect to the walls. Excavated in UE249, it contains unit UE211.
Stratigraphic unit type:  Cut, post hole
[See more]
ID  2233  -  Public access
Description :   UE229. Cut of semicircular shape in plan that continues towards the NE of tomb T2. The visible surface protrudes 17 cm from the profile and is 4 cm deep. No orientation can be seen. It was excavated in unit UE249 and contains unit UE212.
Stratigraphic unit type:  Cut, post hole
[See more]
ID  2235  -  Public access
Description :   UE230. Cut of semicircular shape in plan that partially continues towards the NE of tomb T2. The visible surface protrudes about 27 cm from the profile and is 18 cm deep. The walls fall inwards at an angle of about 100º, until they reach the base, which is oval, and concave, 8 x 5 cm. The walls-base rupture is smooth, and no orientation can be observed. It was excavated in unit UE249 and contains unit UE213.
Stratigraphic unit type:  Cut, post hole
[See more]
ID  2237  -  Public access
Description :   UE231. Cut of circular shape in plan, approximately 13 cm of diameter and a maximum depth of 13 cm. The walls fall inwards at an angle of about 100º until they reach the bottom. The base, also circular (6 cm diameter), is concave with the gentle ruptures with respect to the walls. It has no orientation or inclination and was excavated in UE249. It contains unit UE214.
Stratigraphic unit type:  Cut, post hole
[See more]
ID  2240  -  Public access
Description :   UE232. Cut of circular shape in plant, approximately 20 cm in diameter and a maximum depth of 13 cm. The walls fall inwards at an angle of about 100º until they reach the bottom. The base, also circular (14 cm diameter), is concave with gentle ruptures with respect to the walls. It has no orientation or inclination. It was excavated in unit UE249 and contains unit UE215.
Stratigraphic unit type:  Cut, post hole
[See more]
ID  2242  -  Public access
Description :   UE233. Cut of circular shape in plan, approximately 20 cm in diameter and a maximum depth of 13 cm. The walls fall inwards at an angle of about 100º until they reach the bottom. The base, oval (10 x 4 cm, NW-SE x NE-SW), is concave with soft ruptures with respect to the walls. It has no orientation or inclination. It was excavated in unit UE249 and contains unit UE216.
Stratigraphic unit type:  Cut, post hole
[See more]
ID  2244  -  Public access
Description :   UE234. Cut of circular shape in plan, approximately 20 cm in diameter and a maximum depth of 18 cm. The walls fall inwards at an angle of about 100º until they reach the bottom. The base, oval (9 x 6 cm, ne-sw x nw-se), is concave with soft ruptures with respect to the walls. It has no orientation or inclination. It was excavated in unit UE249 and contains unit UE217.
Stratigraphic unit type:  Cut, post hole
[See more]
ID  2277  -  Public access
Description :   UE249. T2 grave fossa. Rectangular shape cut in a 5.73 m long by 3.16 m wide plan. Its upper perimeter was located at 1.54 m and the lower at 4 m. It has four walls: NE, NW, SW and SE. In vertical section, the pit is staggered and has three levels or horizontal steps at 2.5 m, 3.25 m and 4 m from the surface with 90º breaks between them (walls located between the base of the pit and the middle step and between the middle step and the top step). The wall located between the top step and the edge of the pit is slightly saluted. It cuts the geological substratum and the fossa, burial and filling...
Stratigraphic unit type:  Cut, post hole
[See more]
11-18 of 18 results  
 1 / 2 
    Previous / Next   
"Except where otherwise noted, content on this site is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0. International license."